Disable Unnecessary Services Debian Linux

Disable Unnecessary Services Debian Linux
This article aims to help you increase performance and decrease vulnerabilities by reducing the number of services at minimal level as possible. By reducing the services instructed in this tutorial, domestic users who need regular access to the internet shouldn't experience problems but only improvements, even if not visible.

This article is optimized for those looking for immediate changes or the syntax to manage services on Debian, additionally you can find descriptive information on Systemd at the end.

To begin let's see what services are running to decide what service to discard, to list all services run:

# sudo service --status-all

You will see many services with a plus symbol, these are the services running while the services with a minus symbol are not active.

As you can see all listed services are found at /etc/init.d which is where services are stored. You can run ls on /etc/init.d to check:

# ls /etc/init.d

In my case, a desktop user with a dynamic IP I don't want the mail service because setting UP SPF, DKIM, etc. may not be impossible but messy, therefore I want to disable the active sendmail service. Some other services like ssh, apache, etc. should be removed if you don't use them.

The syntax to disable a service on Debian is:

# sudo systemctl disable

The command to disable sendmail on Debian is

# sudo systemctl disable sendmail

As you can see now the service is disabled

# sudo service --status-all

You can also check for the specific service

# sudo service sendmail status

Currently most Linux distributions don't use System V anymore but use Systemd.
Systemd is a service manager, it is the PID 1, assigns a control group (cgroup) to each service and can be also useful to track the processes.

Through it you can configure services with the system and service manage which initializes in the last boot process step and manages processes executed by the user.

Below there is a list of commands to manage services through SystemD:

# systemctl status

As you can see in the output above SystemD is running.

The following commands lists failed units, services or daemons which didn't start properly due a misconfiguration, unmatched dependency, etc.

Running the following command is a way to audit the device's health.

# systemctl --failed

Unit files contain information on sockets, devices, mount points, swap or partition (.service, .socket, .device, .mount, .automount, .swap, .target, .path, .timer, .slice, or .scope). They may contain information on more options. If Systemd fails to identify an option it will log warnings, options starting by X- are ignored.

To list installed unit files run the following command:

# systemctl list-unit-files

List all running services:

# systemctl

To start a service using systemd run:

# systemctl start

Alternatively you can run:

# sudo service sendmail start

To stop services use the same syntax replacing “start” with “ stop”, to start the run:

# systemctl stop

Similarly, you can use the command “service”:

# sudo service sendmail stop

To restart a service replace “stop” or “start” for “restart”, the following example shows how to start the service “”:

# systemctl restart

You can also command “service” to restart:

# sudo service sendmail stop

To show the status of a specific service use the option “status”, the following example shows how to start  the service :

# systemctl status

You can check a service status using the command “service”:

# sudo service postfix status

As you can see the service says to be masked which means it is strongly disabled and can't be enabled even manually (it can be unmasked but it won't be shown in this tutorial). The following instructions show how to enable services are meant for disabeld services, not for masked ones.

To enable a service to be activated every time the device boots use the option enable, the following example shows how to enable the to be started on boot:

# systemctl enable

To disable a service to remain inactive even after the device boots use the option disable, the following example shows how to enable the no to be started on boot:

# systemctl disable

Additionally to disabling services you can also, and it is recommended, to uninstall any service you are sure you won't use, and even if you plan in the future you can install it, to remove a service, rather than disabling or stopping it, for example to uninstall Apache on Debian run:

# apt remove apache2 -y

You can do the same with all installed services you don't use such as ssh, cups, etc.

There are additional options for systemctl you can find on its man page or online at

I hope you found this article on Disabling Unnecessary Services Debian Linux useful.

Kuidas installida Xenlism Minimalism GTK teema Ubuntu 18-le.04 LTS
Teemade rakendamine on suurepärane viis arvuti välimuse muutmiseks. Täna tutvustame teile veel ühte GTK teemat teie Ubuntu jaoks. Ksenlismi minimalism...
Kuidas installida täielik USB-mälupulgale Ubuntu
Selles õpetuses teeme Ubuntu täieliku installimise USB-mälupulgale. Pange tähele, et see ei tähenda ainult käivitatava Ubuntu Live USB-draivi loomist....
Kuidas installida ja konfigureerida ownCloud Ubuntu 18-s.04 LTS
ownCloud on avatud lähtekoodiga failide jagamise server ja koostööplatvorm. See võimaldab kontrollida andmeid kasutajate serverites ja keskkondades. P...